Teknos tuotteet

Teknoksen offline-tuotetietokirjasto

  • Jälleenmyyjien käyttöön sävytyskoneille Teknoksen tuotetiedot helppokäyttöisessä muodossa.

PANEELIKATTOMAALI Paint for panel ceilings

      

PANEELIKATTOMAALI is a white, water-borne acrylate dispersion paint for ceilings. The paint is very opaque and it prevents bleeding of knots and other dark spots. Finish: matt.

The product has been classified in Emission Classification of building materials to Group M1.

Painting of ceiling panels in dry spaces indoors. For priming and top coating of untreated and previously varnished or painted wooden surfaces.

Technical Data

Solids

About 40 % by volume

Volatile organic compound (VOC)

EU VOC limit value (kat A/a): 30 g/l. The product's VOC: max. 30 g/l.

Practical spreading rate

6 - 8 m²/l

Density

1.3 g/ml

Drying time +23 °C, the relative air humidity 50 %

- dust free

- overcoatable

after 1 hour

after 3 hours

The drying process will be slower in cold and/or damp.

Thinner, clean up

Water. Wash the equipment immediately after use with detergent and warm water.

Finish

Matt

Colours

White T1326 (NCS S 0500-N)

Washability and wear resistance

Wear resistance of the painted surface is good.

Wet scrub resistance, class 1 according to EN 13300 (ISO 11998).

Packages (availability varies by country)

White: 2,7 L, 9 L

SAFETY MARKINGS

See Safety Data Sheet.
Direction for Use

Surface preparation

Clean new wooden surfaces from dust and dirt.

Wash dirty previously varnished or painted surfaces with RENSA SUPER paint cleaner. Remove loose and poorly adherent varnish or paint coats. If the wooden surface has previously been oiled or waxed, the suitability of PANEELIKATTOMAALI to the surface must be ensured with a test painting.

Priming

Priming with unthinned PANEELIKATTOMAALI.

Application

Before use stir the paint thoroughly.

Apply PANEELIKATTOMAALI by brush. Also roller or airless spray may be used for application, but the surface must be finished with a brush especially when priming unpainted wood.

Recommended nozzle size for airless spray is 0.015 - 0.019''.

Conditions

The surface to be painted must be dry. During the application and drying period the temperature of the ambient air, the surface and the paint shall be above +10 °C and the relative air humidity below 80 %.

Good ventilation during the application and drying period quickens the drying process.

Surface maintenance

The final forming of the paint film takes 3 - 4 weeks under normal circumstances and after that the ultimate durability and hardness is reached. Before this the painted surface must be treated with care.

The painted surface can be cleaned by wiping with a neutral (pH 6 - 8) detergent. For very dirty surfaces can also alkalescent (pH 8 - 10) detergents be used. Detergent and dirt are removed by wiping and/or rinsing the surface with clean water. Use a cleaning cloth, soft sponge or similar for cleaning. Avoid coarse brushing or heavy abrasion. Follow the dilution and other instructions of the detergent producer when using detergents.

Storage

Must not freeze.

The information of this data sheet is based on laboratory tests and practical experience. The figures are for guidance only and depend on, for example, colour and gloss. As we have no control over the use and application conditions, we are only responsible for the quality of the product and guarantee that it conforms to our quality control. We accept no liability for any loss or damage resulting from the application of the product contrary to the directions or the intended use. The latest versions of our data sheets, material safety data sheets and system sheets are on our home pages www.teknos.com.