NORDICA MATT House Paint
Full-matt water-borne acrylate-based paint for wooden surfaces outdoors. NORDICA MATT has a matt and hard surface that is dirt-repellent and retains its appearance and colour for a very long time.
For new and previously with acrylate- and oil paint painted wooden surfaces and for industrially primed and/or undercoated wooden surfaces, e.g. exterior walls, facial boards and weather boards.
| Technical Data | |
|---|---|
Solids | About 36 % by volume |
Volatile organic compound (VOC) | EU VOC limit value (kat A/d): 130 g/l. The product's VOC: max. 130 g/l. |
Practical spreading rate | 5 - 8 m²/l |
Density | 1.2 g/ml |
Drying time at +23 °C / 50 % RH - touch dry - overcoatable | after 1 hour after 4 hours The drying process will be slower in cold and/or damp. |
Thinner, clean up | Water. Wash the equipment immediately after use with detergent and warm water. |
Finish | Full-matt |
Colours | Base 1 (white), base 3, base 5 (red) and black standard colour The paint is included in the Teknomix tinting system. |
Weather resistance | Very good. |
Packages (availability varies by country) | Base paints 1 and 3: 0,45 L, 0,9 L, 2,7 L, 9 L, 18 L Base paint 5: 0,9 L, 2,7 L, 9 L, 18 L Standard colour: 0,9 L, 2,7 L, 9 L |
SAFETY MARKINGS | See Safety Data Sheet. |
| Direction for Use | |
|---|---|
Surface preparation | NEW WOODEN SURFACE: Treat the surface as soon as possible. At least the impregnation and priming would be best done in the summer of construction. Remove from the surface all loose matter, dirt, dust and mildew. If needed, use RENSA FACADE facade cleaner. PREVIOUSLY PAINTED OR OLD WOODEN SURFACE: Replace wooden parts that are in poor condition. Remove loose matter, dirt and dust. Remove loose and poorly adherent old paint. Wash the surface with RENSA FACADE facade cleaner. Remove the deteriorated paint coats carefully. The adherence of an old thick paint layer to the substrate may have been weakened, therefore the paint should be removed completely although the paint film looks intact. The old paint layer is removed by scraping, by wire brushing or by burning off (e.g. by warm-air heater or infrared heater). Secondarily paint remover or blasting can be used. Clean rusty steel parts: by sanding, wire brushing eg. |
Priming | Bare wooden surface is primed with clear WOODEX AQUA BASE priming oil. If the wooden surface is old and primed with oil or painted with oil paint, solvent-borne WOODEX BASE priming oil is used. |
Priming | The surface treated with priming oil is then primed with NORDICA PRIMER. If the surface is an old wooden surface primed with oil or painted with oil paint, use solvent-borne PUUPOHJA alkyd primer diluted 10-15 % by volume. Rusting steel surfaces are primed with FERREX AQUA anticorrosive paint. Also the end grains of industrially primed and/or undercoated timber needs to be treated with priming oil or primed before applying top coat. |
Top coating | Before use stir the paint thoroughly. Dilute the paint 5 - 10 % by volume by water, when required. Reserve a sufficient amount of paint in the same vessel for each uniform surface. Colour differences will thus be avoided. Apply the paint by brush. If the paint is applied by airless spray, the surface is to be finished by a brush. Recommended airless spray nozzle is 0.015 - 0.019". |
Application conditions | The surface to be painted has to be dry. The moisture of the wood must be below 20 % of the dry weight of the wood. During the application and drying period (also the following night after the painting work needs to be taken into account), the temperature of the ambient air, the surface and the paint shall be above +5 °C and the relative air humidity below 80 %. |
Storage | Must not freeze. |
Technical Data Sheet
Product Image (Hi-Res)