TIMANTTI 7 Matt special acrylate
Water-borne acrylate dispersion paint for walls and ceilings indoors. Mildew-resistant.
Finish: matt.
The product has been classified to Group M1 in Emission Classification of building materials.
Especially suited for use on walls and ceilings in dry and humid spaces where good washability and abrasion resistance is required, e.g. in halls, staircases, kindergartens, schools, hospitals, food processing premises and other similar facilities.
TIMANTTI 7 can be applied to primed concrete, plaster, stopper, brick, and building board surfaces according to the painting directions. The paint is also suitable for repainting old alkyd and dispersion paint coats.
| Technical Data | |
|---|---|
Solids | About 40 % by volume |
Volatile organic compound (VOC) | EU VOC limit value (kat A/a): 30 g/l. The product's VOC: max. 30 g/l. |
Practical spreading rate | Previously painted surface Filler and wood fibre board Concrete and plastered surface 7 - 10 m²/l 6 - 8 m²/l 4 - 7 m²/l |
Density | 1.3 g/ml |
Drying time +23 °C, the relative air humidity 50 % - dust free - overcoatable | after 1 hour after 2 hours The drying will be slowed down if the air is cool and/or humid. |
Thinner, clean up | Water. Wash the equipment immediately after use with detergent and warm water. |
Finish | Matt, gloss abt. 7 (at 60° angle) |
Colours | Base paints 1 and 3, which can be tinted to obtain the shades in Interior Colour Cards. |
Washability and wear resistance | Wear resistance of the painted surface is very good. The painted surface can be washed repeatedly. Wet scrub resistance, class 1 according to EN 13300 (ISO 11998). |
Packages (availability varies by country) | 2,7 L, 9 L, 18 L |
SAFETY MARKINGS | See Safety Data Sheet. |
| Direction for Use | |
|---|---|
Surface preparation | Clean the surface from dirt and dust. Wash previously painted, dirty surfaces with RENSA SUPER paint cleaner. Matt down hard or gloss surfaces by sanding and thereafter remove the dust. For smoothing of irregularities in the surface choose a suitable filler from the SILORA series. The dried filler is sanded down and the dust removed. |
Priming | HUMID AREAS: Prime concrete, plaster, stopper, brick, and building board surfaces with TIMANTTI W moisture sealer according to the directions for use. IN DRY AREAS prime the surfaces previously mentioned with TIMANTTI 3 Primer. Steel surfaces are primed with FERREX AQUA Anticorrosive paint. Prime galvanized surfaces with TIMANTTI 3 Primer. |
Application | Before use stir the paint thoroughly. The paint can be diluted with water, if required, but dilution may impair the coverage of the paint. Apply by roller, spray or brush. Recommended nozzle size for airless spray is 0.017 - 0.021''. |
Conditions | The surface to be painted must be dry. During the application and drying period the temperature of the ambient air, the surface and the paint shall be above +5 °C and the relative air humidity below 80 %. Drying is faster in low air humidity and/or above + 21 °C. Application will be easier if air is humidified and/or temperature is lowered in the working space. Ventilation after the painting will quicken the drying. |
Surface maintenance | The final forming of the paint film takes abt. 4 weeks under normal circumstances and after that the ultimate durability and hardness is reached. Before this the painted surface must be treated with care. The painted surface can be cleaned by wiping with a neutral (pH 6 - 8) detergent. For very dirty surfaces can also alkalescent (pH 8 - 10) detergents be used. Detergent and dirt are removed by wiping and/or rinsing the surface with clean water. Use a cleaning cloth, soft sponge or similar for cleaning. Avoid coarse brushing or heavy abrasion. Follow the dilution and other instructions of the detergent producer when using detergents. |
Storage | Must not freeze. |
Technical Data Sheet
Product Image (Hi-Res)