NORDICA AQUA Oil paint
A water-borne, semigloss oil paint for wooden surfaces outdoors.
New and previously painted wooden surfaces, e.g. facades, facial boards, weather boards and window boards. Not suitable on surfaces painted with dispersion paints.
| Technical Data | |
|---|---|
Solids | About 47 % by volume |
Volatile organic compound (VOC) | EU VOC limit value (kat A/d): 130 g/l 2010. The product´s VOC: max. 130 g/l. |
Practical spreading rate | Planed timber Sawn timber 8 - 10 m²/l 5 - 7 m²/l |
Density | 1.2 g/ml |
Drying time, +23 °C - rain proof - overcoatable | after 6 hours after 1 - 3 days The drying process will be slower in cold and/or damp. |
Thinner, clean up | Water. Wash the equipment immediately after use with detergent and warm water. |
Finish | Semigloss |
Colours | Base paints 1 and 3. According to the Colour Cards for exterior paints |
Weather resistance | Good Notice that it is typical for oil paints that their colour and gloss change in the cause of time. |
Packages (availability varies by country) | Base paint 1: 0,9 L, 2,7 L, 9 L, 18 L Base paint 3: 0,9 L, 2,7 L, 9 L, 18 L |
SAFETY MARKINGS | See Material Safety Data Sheet. NOTE! Because of the danger of self-ignition, any waste from the product, spray mist and soiled rags etc. are to be kept in a fire-proof place in air-tight containers. Immersion in water is also recommended. |
| Direction for Use | |
|---|---|
Surface preparation and priming | NEW WOODEN SURFACE: Treat the surface as soon as possible. At least the impregnation and priming would be best done in the summer of construction. Remove from the surface all loose matter, dirt, dust and mildew. If needed, use RENSA HOMEPESULIUOS Mildew Remover. Apply a coat of clear WOODEX AQUA BASE priming oil. Allow to dry for one day. Prime wooden surfaces with 5-10 % diluted NORDICA PRIMER and allow the surfaces to dry for 1 - 3 days depending on the weather. Wash the metal parts with TEKNOSOLV 1621 (solvent naphtha) and prime with FERREX. PREVIOUSLY PAINTED OR OLD WOODEN SURFACE: Change the deteriorated wooden parts to new ones. Remove loose matter, dirt and dust. Remove the deteriorated paint coats entirely. Note, that the adherence of an old thick paint layer to the substrate may have been weakened, therefore the paint should be removed although the paint film looks intact. The old paint layer is removed primarily by scraping or wire brushing and possibly by heating the surface with infra-red heater designed for that purpose. Secondarily paint remover or blasting can be used. Wash painted surfaces with RENSA MAALARINPESULIUOS Paint Washing Liquid, mildewed surfaces with RENSA HOMEPESULIUOS Mildew Remover and rinse the surfaces thoroughly. Old, untreated wooden surfaces can before the priming be treated with clear WOODEX AQUA BASE priming oil, see ´NEW WOODEN SURFACE´. Prime bare wooden surfaces with NORDICA PRIMER, diluted 5-10%. Allow to dry for 1 to 3 days depending on the weather. Wire-brush the rusty metal parts. Wash all metal parts with TEKNOSOLV 1621 (solvent naphtha) and prime with FERREX. |
Top coating | Reserve a sufficient amount of paint in the same vessel for each uniform surface. Colour differences will thus be avoided. Stir the paint well and apply by paint brush or spray once or twice. |
Application conditions | The surface to be painted must be dry. The moisture of the wood must be below 20 % of the dry weight of the wood. During the application and drying period the temperature of the ambient air, the surface and the paint shall be above +5 °C and the relative air humidity below 80 %. Avoid application in direct sunlight. |
Storage | Must not freeze. |
Technical Data Sheet
Product Image (Hi-Res)